Motorcycle wrap 0728
Motorcycle wrap 0430
Vinyl Wrap Motorcycle

Vinyl Wrap Motorcycle Vinyl Wrap Motorcycle

Sort By: Featured Items Newest Items Best Selling A to Z Z to A By Review Price: Ascending Price: Descending

From my experience, 3M is the leader in the high-performance film.  As a product developed with 3M’s vast experience; it’s really like the Ferrari of wraps.  No other product comes near.

If you find out you have a bubble or crease, don’t panic. As long as you’ve not applied pressure to the pressure-activated adhesive, you’ll be able to pull the wrap and apply a little heat to shrink the surface back to its former state and try again. If you’ve applied pressure, you can sometimes gently pull the wrap back but be careful, if you’re pulling and it’s proving difficult you might just have to accept a small crease. The tip here is; don’t apply pressure on a crease.

Remove the backing and apply the vinyl to the flattest part of the panel first to create a baseline. You’re then going to use your felt pad to work the wrap ongoing from side to side slowly. At this stage, you want to keep the vinyl as level as possible.

You want to be in an area with decent lighting and minimal air flow as wind could catch your wrap and cause creases, and also blow dust into the air sticking to the adhesive. I’ve heard a lot of professionals say you can’t wrap outside, I personally disagree. I’ve wrapped my Mercedes-Benz Viano twice [4 years apart] outside and both times saw a perfect finish. You want it to be dry, dust and wind free but I say outside is okay if it’s a mid-range temperature.

Included in all our bike wrap kits is our bubble free wrap, a Felt edge Squeegee and a precision cutting blade. Check out our video’s to see how easy it is to apply.

Finally, you need to overwrite the wraps memory of being flat and un-stretched. Here you want to heat to 80-90ºC. I tend to crank my heat gun up high and play it by guesswork, but if you’ve got the gadget, you can use an infra-red temperature gauge to be sure that you have reached this temperature. I’ve not had problems without it, but I’m sure a professional would tell you otherwise.

Decent lighting Minimal air flow Dust free environment Surface / table you can move around Something to prop the item on Within reach of electrics for heat gun

Overall Rating Wrapping gives your ride a totally new looks for a fraction of the cost and also protects your paintwork. It does take time and patience, but it’s so worth it for the finish and bragging rights.

Having said that, and given that removable motorcycle parts are mostly small in size; I would recommend doing the bike inside. My ideal is on a table where you’re able to move around the table instead of having to spin the object, such as a tank constantly.

For a motorcycle like a Sportster or DYNA if you buy 3 metres x 1.5 metres of wrap you’ll have more than enough [just in case you have to restart a piece]. Alcohol will be a few quid, along with a foam pad. As you’re doing it yourself, it’s a labour of love, so time is all it’ll cost.

Finally, think about items you can use to support the item being wrapped while wrapping. A friend is the easiest option but if you’re wrapping solo anything from a large cooking bowl to support a fender can be a great aid leaving you with two hands to manipulate the wrap.

Depending on your work surface you might want to put some protection down to both protect your table from sharp corners of the fender and also protect the paintwork from the hard surface. I just used some soft packaging – make sure it won’t leave bits on your wrap.

Should you wish to remove the wrap, simply apply a little heat and gently pull the wrap away. It’s an easy job but take it steady. Once off you’ll need to use an adhesive cleaner or alcohol to clean off the remaining glue.

I estimate wrapping your bike to cost about £120 / €150 / $170

Make sure you get both the wrap and substrate temperature gradually as anything less will see the vinyl retain its memory resulting in it popping out of recesses and curves – maybe not immediately but in time. It’s vital this is carefully done on all stretched areas and recesses but be careful not to overheat as that will damage the wrap.

The Complete Guide to Wrapping Harley Davidson DYNA StreetBob 2015

Why paint your bike when you can wrap it with vinyl. Our bike wraps are made especially for exterior wrapping and are perfect for giving your motorbike, Moped or ATV a makeover at a fraction of the cost of a paint job.

Here’s the magic, heat allows it to stretch but then heat also allows it to shrink back to its original form due to thermal material memory! It’s truly witchcraft! Whatever it is, it’s exactly what you need for wrapping something as tricky as a motorcycle as I can guarantee you won’t stretch it perfectly first time. It means you can heat stretch, apply pressure, remove, heat shrink, heat stretch, and apply… over and over. It’s an incredibly forgiving material.

We also sell all our vinyls in many other sizes, small or large! Browse in the Automotive Section for our full range of over 200 colours and styles.  

Pull back the wrap and try again, using heat to return wrap to original from Pin prick bubbles and gently heat while pushing the air out

With a motorcycle [or car] you need to ensure you give yourself the easiest surface possible to wrap. I’d, therefore, recommend removing any panels you can so you can twist, turn and work around the part while wrapping. This includes tanks, fairings, battery covers, fenders etc. Once apart, it’s time to clean. This is vital as any dirt, dust or oil will impede the vinyl’s ability to stick. I recommend a hot soapy wash to clean the worst; Fairy Liquid can be a good one for busting grease. Make sure you allow it plenty of time to fully dry! You then want to use isopropyl alcohol to ensure the surface is 100% clean and grease free. For this make sure you use a lint free cloth to leave a pristine surface. Also, while the wrap does cover your paintwork up, it does show things through as it will follow all contours. My general rule – if you can feel it, it will likely show up. Therefore, if you have any scratches, dents or rust, you will want to treat them first to ensure a smooth surface. Once clean, be careful to keep your grubby fingers off the surface. Cleaning needs:

Be careful not to scratch your bike when cutting, I always try to cut away from the surface and then push the final bit of wrap down smooth.

Bubbles are easier to deal with if you can’t pull back. The first option is to give it five minutes; the air permeable properties might allow it to dissipate out with time. If this doesn’t work, use a pin or knife point to make a small puncture, then apply a little heat and push the air out.

You’ll find that you won’t get the required stretch in one, you’ll likely need to stretch and apply a small section, and then heat shrinks it, before then stretching again for the next small section. You do want to be careful not to demand too much stretch and shrink from the material, but you’ll find it exciting to do this multiple times. Plus, because modern adhesive reaches its most sticky state after 24 hours, it makes the wrap repositionable over and over [within limits].

I recommend using a 3M primer to give the wrap little extra support in sticking. Simply using a small brush to apply it around the edge and give it around 90 seconds to cure before continuing.

Once you’ve fully wrapped the visible surface, you want to tidy off the underside. Always try to wrap around into the non-visible area, for example, the underside of the fender. With these areas, it’s important you get a nice stick, but it really doesn’t matter how rough it looks as no one can see it.

How long is a piece of string? This will really come down to experience. My first tank on the Street Bob took 5.5 hours but it’s probably one of the hardest tank shapes to do due to its fish tank shape – it was also the first tank I’ve done. The Forty-Eight Sportster only took 3 hours in comparison. A fender would be about 45 minutes while a battery covers 30.

At this point, things should be starting to look pretty awesome. It’s time to get a very sharp knife to trim. I prefer to use a Stanley knife blade as it’s really small and easy to use around the contours. I recommend leaving a minimum of 15mm overlap around the underside.

Heating the wrap will allow a material stretch up to 40 percent before distorting Heating also allows the wrap to shrink back to its original form via material memory If you crease or crumple the wrap, simply pull it apart, and heat will see it return to its original form Heat with a hot hair dryer or gentle heat gun–if it burns your fingers it will burn your wrap – turn the temperature down or move further away

Remove parts from bike Give a hot soapy wash Treat any dents, rust and contours Use lint free cloth and isopropyl alcohol

A tip for wrapping a fuel tank is to use a large picture frame. Here you will stick the edge of the wrap to the frame, so it’s held flat across the frame. You can then have one person holding the frame while the other heats up the whole wrap surface. Once warm and supple, you can apply even tension to the full parameter of the frame and work the wrap down onto the tank. This will only work for the first section, but it massively helps you get started without too much crumpling around the edges.

When stretching the vinyl be careful to always pull outwards from the already applied area using a large section to spread the tension. This is to ensure a nice even stretch. This also applies when you use extra heat to soften and stretch the vinyl, apply heat to a larger area than you need as this should help to avoid you distorting the material.

Remember, I’m an account director in marketing…not a mechanic or engineer…so if

Tools Needed 3M wrap [don’t buy a cheaper alternative] 3M primer [for complex areas] Lint-free cloth Isopropyl alcohol Felt pad [or soft flat edged item roughly credit card sized] Stanley knife blade Heat gun or decent hair dryer Large picture frame [for wrapping tanks] Why only 3m?

Transforming my beast with a matt metallic blue vinyl wrap, it’s happening! #custom #3m #dewalt Stay tuned for finished shot or head to Reading Harley Davidson’s Sunday event and say hi!! Excited 😎✌️@rebelsride @grosvenorcasinos #wrap #wrapped #vinyl #vinylwrap #3mvinyl #3mvinylwrap #working #satisfaction #vehicle #exotic #tank #followme #HarleyDavidson #StreetBob #bikerchick #HarleyLife #bikegirl #motorbike #blonde #motorcycle #bike #biker #instabike #instamotor #motorbike #ukbikers #TheGirlOnABike

You can then buy it on eBay, Amazon or search Google to look for the cheapest source. As long as you’re careful to ensure its genuine 3M branded wrap, you can go for the cheapest outlet.

A post shared by 🇬🇧 Vanessa 🇬🇧 (@thegirlonabike) on Jun 29, 2016 at 3:04pm PDT

Highlights New look for a fraction of the cost Satisfaction of doing it yourself Totally achievable as an amateur

Once you’ve worked in the wrap to a basic level, you’re going to need to start using some heat. The beauty of 3M wrap is its ability to stretch to up to 40 percent so it can be molded around curves and edges.

I recommend making sure you start at a time when you know you have a decent chunk of time [including light] so not to rush or feel pressured. I would also recommend not trying to do it all in one sitting as it is mentally rather tiring.

Once the wrap is where you want it, you need to apply firm pressure with your felt pad as it’s a pressure-activated adhesive. You’ll do this gradually as you go.

The world is pretty much your oyster here, these wraps come in literally all colours and patterns, whether it’s a matte look, gloss or even carbon fibre effect you’re after. If you can imagine it, you can probably find it. I’d recommend taking a look at the colours available on the 3M website to select your finish and colour.

Start by roughly cutting a section of wrap slightly larger than the item being wrapped. Always go larger than the area being wrapped to allow a safety net and to give an area to touch when applying and manipulating on it. Give the surface a final check to make sure it’s clean.

These Motorbike Wrap Kits come in different sizes for Scooters/Mopeds, ATV Quads, Dirt/Enduro Bikes, Sportsbikes and Tourers. 

Honest answer. It’s tricky. It takes patience and a steady hand. But! It is achievable even without being a professional. The pros will tell you it’s not a home job, but I’m proof it can be.

I would encourage everyone to give it a go, and I hope the below helps arm you with all the information you need on how to vinyl wrap your motorcycle or car successfully.

Wrapping the beast! When you’re bored of a matt black van it’s time to for blue metallic! Mixing it up! This is the second time I’ve done the whole van, it’s a slow very careful job but so satisfying. And at the end you pretty much have a new vehicle in any colour you want. Tip to anyone thinking of doing theirs: I would only ever use 3m vinyl wrap! Best stuff on the market – like the Dewalt of vinyl wrap! Full finished shot to come! It’s a big job so give me a few weeks 😉💪 #3m #wrap #wrapped #vinyl #vinylwrap #3mvinyl #3mvinylwraps #mercedes #mercedesbenz #viano #vito #dewalt #working #satisfaction #cars #car #sportscar #vehicle #vehicles #exotic #exoticcar #exoticcars #speed #tires #race #wheels #V6 #engine #horsepower #TheGirlOnABike

Once, you’ve done the easier flat areas you should stretch the vinyl without heat over the whole area. Don’t be tempted to work the film into the more complicated areas yet; this will come gradually.

Mega! The bragging right of being able to say you wrapped it yourself is awesome. If you pick the right colour, the light will pop like no paintwork and draw attention. Wrapping, and the ability to simply change colour when you fancy it means you can trick people with your new ride [which is simply a new wrap].

Tips From Experience Have a friend help, 4 hands make it a lot easier than 2 Start with an easier item with the least amount of contour, leave the tank to last! Avoid wrapping in cold weather Leave plenty of time – don’t try and do it in a rush Don’t start if you’re tired, you need patience and energy Have some snacks and a kettle for tea/coffee nearby to keep you fuelled If the heat gun burns your fingers it will burn the wrap Be prepared to write off some wrap and start again if it goes wrong

Yes, there are cheaper competitor brands out there, but ultimately, wrapping is a tricky game so why make it harder with inferior materials. Buy the best and make life easier for yourself.

A post shared by 🇬🇧 Vanessa 🇬🇧 (@thegirlonabike) on Jun 7, 2016 at 11:36pm PDT

Use heat to ensure the wrap is nice and supple and then gently pull the wrap around the underside in sections.

It comes ready to use right out of the box as a self-adhesive vinyl It handles easily, with a perfect balance between flex and rigidity It’s semi-permeable allowing to escape, preventing and eliminating bubbles It is a pressure-activated adhesive, which enables you to apply and reposition until you have the perfect finish.

If there is no underside, such as on a fairing, simply cut along the edge line of the item.

Related Images of Vinyl Wrap Motorcycle
The final article
Stickerbomb wrap bike kit vinyl tools
Over 10 kinds camo vinyl wrap car motorcycle decal mirror phone laptop diy styling camouflage sticker film sheet in car stickers from automobiles
Ninja motorcycle wrap
Motorcycle vinyl wrap cover
Custom vinyl wrap for motorcycle designed printed installed by car wrap solutions in fort lauderdale florida
Recent work recent work
Get your motorcycle wrapped at vivid wraps
3d 38mm x 45mm carbon fibre bubble free vinyl wrap for cars and motorcycles motorbikes scooters
Custom motorcycle graphics
Motorcycle vinyl wrap for harley davidson designed printed installed by car wrap solutions in fort lauderdale florida
Motorcycle vinyl wrap curves
Motorcycle wrap 0874
Motorcycle wrap 0504
Digitally printed wraps
Textured wrap
Related Post of Vinyl Wrap Motorcycle
Raider J 110 Sticker Design

Raider J 110 Sticker Design

Raider J 110 Sticker Design Raider J 110 Sticker Design Raider J 110 Sticker Design . . . . . […]
Custom Stickers Okc

Custom Stickers Okc

Custom Stickers Okc Custom Stickers Okc Custom Stickers Okc Team okc velo name stickers vcgraphix. Oklahoma city thunder ps4 skin […]
Decal Stickers Car

Decal Stickers Car

Decal Stickers Car Decal Stickers Car Decal Stickers Car . . . . . . . . . . . […]
Decal Stickers Etsy

Decal Stickers Etsy

Decal Stickers Etsy Decal Stickers Etsy Decal Stickers Etsy . . . . . . . . . . . […]